欧美丰满大乳高跟鞋_国产精品无码一区二区三区_国产精品午夜无码av体验区_国产精品狼人久久久久影院

細分旋渦氣泵的簡單故障及排除方法
1、氣泵壓力或流量降低：
當出現壓力和流量下降時，首先切斷旋渦氣泵的電源，查看進氣口是否有東西堵塞，檢查進氣口過濾網，不過不要拆除過濾網，否則會把雜物吸進氣泵，導致損壞。其次，若發現機器內部有雜物的，導致橡膠皮頂住了電磁鐵，造成電磁鐵不能恢復位置。此時可以打開旋渦氣泵的外殼，清理內部雜物。在橡膠皮上鉆一個小孔，排除負壓產生的吸附作用即可。若非雜物因素造成的壓力或流量下降，用于 切紙機氣泵和絲印機風泵 , 照排機 風泵等一些帶閥門的氣泵則依次檢查以下部分：是否是閥桿卡住或閥門開啟度過大，電磁閥閥桿缺少潤滑油或閥桿同心度偏移,也會造成壓力和風量的降低，只要加適量的潤滑油、調整電磁閥桿的的同心度或調整進氣流量閥和出氣釋壓閥就可以了。同時注意盡量不要觸碰電磁鐵。電機的缺相或運轉方向不對也是造成此類故障的一個原因，此時應檢查并重新接好電源 , 如果電機燒壞 , 應更換同型號電機 , 單相電機檢查電容是否完好 , 接線是否正確。

2、氣泵噪聲變大
首先檢查旋渦氣泵泵體內是否有雜物，如有，則 打開外殼 , 清理內部雜物；其次檢查葉輪是否卡住，此時聯系廠家修理，需要重新裝配才能消除故障。第三檢查軸承是否損壞，必要時更換軸承。

3、泵體溫升高
首先檢查進氣口是否堵塞， 清洗進氣口過濾網 , 但不能拆除，否則將會吸進雜物損壞氣泵絲印及照排機及其它需要吸力的機械設備。請適當保持氣泵的工作時間隙。其次檢查機體內有雜物，打開外殼 , 清理內部雜物。